Stepper motor & encoder
LPC-2.ED1 | Encoder stepper motor driver module
- Bipolar stepper motor drive outputs (A, B, C, D) with 500 mA or 330 mA drive capability each
- Internal +24 V DC or external 5 .. 36 V DC stepper motor power supply selection with jumper J6
- Encoder inputs for incremental or count operation (A, A\; B, B\; Z, Z\)
- Internal +5 V DC or +12 V DC encoder power supply selection with jumper J1
- Encoder inputs type (RS-485 or TTL with pull up to +5 V DC) selection with jumpers J3 (A,A\), J4 (B,B\) and J5 (Z,Z\)
- Standard DIN EN50022-35 rail mounting
USER MANUAL
Differential pressure modules
LPC-2.VV4 | Differential pressure I/O module
- Differential pressure measurement up to 500 Pa
- 3 x Voltage analog inputs: 0 .. 10 V
- 1 x Voltage analog output: 0 .. 10 V
- 1 x NTC 10k input
- 1 x NTC 10k / voltage analog input: 0 .. 10 V, jumper selectable
- 8 x Digital inputs
- 2 x Relay outputs, NO
- 2 x Relay outputs, NO / NC, jumper selectable
- Standard DIN EN50022-35 rail mounting
USER MANUAL
LPC-2.VV1 | Differential pressure sensor module
- Differential pressure measurement up to 1000 Pa
- Standard DIN EN50022-35 rail mounting
USER MANUAL
Special digital outputs
LPC-2.SO2 | Power supply module
- Power supply module with 5.6 .. 12 V DC output for other devices
- Standard DIN EN50022-35 rail mounting
USER MANUAL
LPC-2.DOL | Door lock output module
- Door lock open module for 12 V DC low current locks
- Standard DIN EN50022-35 rail mounting
USER MANUAL
Dimmer outputs
LPC-2.DD2 | Triac dimmer module
- Triac current drive for dimmable lights or motor drives
- Operational power supply 100 .. 253 V AC, 50/60 Hz
- Load current up to 0.9 A
- Standard DIN EN50022-35 rail mounting
USER MANUAL
LPC-2.DD4 | 4 channel MOSFET dimmer module
- 4 channel MOSFET dimmer drive for dimmable lights or AC motor fans.
- Operational power supply 90 .. 264 V AC, 50/60 Hz or 11.5 .. 30 V DC.
- Overload protected
- SW adjustable trailing-edge or leading-edge dimmer type, separately for each one of 4 channels.
- SW adjustable fade-in and fade-out time effect, separately for each one of 4 channels.
- Phase dependent driver for output which makes this module a lot more resistant to electrical disturbances than commonly used amplitude dependent drivers.
- Standard DIN EN50022-35 rail mounting
USER MANUAL
LPC-2.PW1 | 4 channel PWM signal output module
- 4 channel PWM signal output
- Galvanic isolated outputs
- 100 mA per output with overload protection
- Push-pull transistor outputs capable of driving the signal over up to 100 nF capacitance on the lines.
- Adjustable transition time (fade effect) between various output settings
- Status LEDs
- Standard DIN EN50022-35 rail mounting
USER MANUAL
Room modules
LPC-2.R01 | 7DO 6DI room module
- 7 triac outputs
- Electrical door lock output
- 6 voltage free digital inputs
- Galvanic isolated
- Flexible inputs for wide use of operation
- Standard DIN EN50022-35 rail mounting
USER MANUAL
LPC-2.R02 | 4DO 3DI 4AO 2AI room module
- 4 analog outputs, where Q2 and Q4 may also be used for GND connection (jumper selectable)
- 2 analog inputs, where I2 input may also be used for NTC or GND connection (jumper selectable)
- Analog input voltage range: 0 .. 10 V @ ±1 % measurement error of full scale
- Analog output voltage output range: 0 .. 10 V @ ±1 % accuracy of full scale value
- Tacho input
- 3 voltage free digital inputs, galvanic isolated
- Flexible digital input for wide use of operation
- 3 snubberless zero crossing triacs output also suitable for use with inductive loads up to 0.9 A
- 1 snubberless zero crossing triac output also suitable for use with inductive loads up to 3.5 A, with load test function
- 24 V AC/DC power supply output with overload protection
- Standard DIN EN50022-35 rail mounting
USER MANUAL